SATO GL408e / GL412e Návod k obsluze stáhnout pdf (Strana 38)

Unit 4: Printer Configuration

GL408-412e Operator’s Manual

4-2

PRINTER CONFIGURATION

This unit provides in-depth instruction on printer configuration for operation and for some troubleshooting.

The printer may be configured via the buttons and/or potentiometers loacated on the printer’s operator panel. All of

the printer’s buttons, switches, and potentiometers are used either singularly, or in conjunction, to perform

configuration activities.

Refer to the Control Features chapter of the Introduction unit for identification of specific interface features.

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 147 148

GL4xxe Operator’s Manual 1
PN: 9001163B 2
TABLE OF CONTENTS 3
INTRODUCTION 6
ABOUT THIS MANUAL 7
GENERAL DESCRIPTION 8
CONTROL FEATURES 9
TECHNICAL DATA 10
Unit 2: Technical Data 11
GL408-412e Operator’s Manual 11
REGULATORY 12
CHARACTER FONT CAPABILITIES 13
BARCODE CAPABILTIES 14
INSTALLATION 15
Accessory Box 16
Shipping Container 16
PRINTER INSTALLATION 17
MEDIA SELECTION 18
MEDIA & RIBBON LOADING 18
Figure 3-3c, Ribbon Loading 19
CONTINUOUS MODE 20
TEAR-OFF MODE 20
CUTTER MODE 20
DISPENSE MODE 20
LINERLESS MODE 20
LABEL PRINT DIRECTION 21
INTERFACE SELECTION 22
READY/BUSY INTERFACE SIGNALS 23
SIGNAL SIGNAL DEFINITION 23
READY/BUSY CABLE REQUIREMENTS 23
IEEE1284 PARALLEL INTERFACE 24
1 To Host 32 Fault To Host 24
1 From Host 24
UNIVERSAL SERIAL BUS (USB) 25
802.11G WIRELESS 26
WIRELESS LAN SIGNAL STRENGTH 27
SOFTWARE SPECIFICATIONS 27
ALL INTERFACES 28
STATUS5 TIMING CHARTS 29
NORMAL PROCESS 29
CANCEL PROCESS 29
ERROR PROCESS 29
PRINT PROCESS 30
COMMAND PROCESS 30
BCC ERROR PROCESS 30
EXTERNAL SIGNAL 31
25-PIN CONNECTOR ASSIGNMENTS 32
INPUT SIGNAL WAVE FORM 33
START PRINTING 33
REPRINTING 33
OUTPUT SIGNAL WAVE FORM 34
BASIC OPERATION 34
PAPER END 34
RIBBON END 34
MACHINE ERROR 34
Unit 3: Installation 35
ACCESSORIES INSTALLATION 36
CONFIGURATION 37
PRINTER CONFIGURATION 38
CONFIGURATION MODES 39
CONFIGURATION MODE 40
ADVANCED MODE 41
SERIAL INTERFACE MODE 43
PARALLEL INTERFACE MODE 44
CENTRONICS INTERFACE MODE 45
PGL EMULATION MODE 49
ZGL EMULATION MODE 50
DGL EMULATION MODE 51
TGL EMULATION MODE 52
IGL EMULATION MODE 53
DIAGNOSTICS MODE 54
PRINTER MANAGEMENT MODE 55
DISPLAY INTENSITY ADJUSTMENT 56
BUFFER CLEAR 56
SOFT RESET 57
KEY LOCK/UNLOCK 57
INTERFACES 58
USER MODE (TABLE 4-1) 59
ADVANCED MODE (TABLE 4-3) 65
Data Protocol 78
Buffer Size in K 78
EMULATION 98
MENU DESCRIPTION 100
IGL Setup 118
Save state* 118
Priority Setting 118
Command* 118
Error Log Clear 120
TROUBLESHOOTING 125
ERROR SIGNAL TROUBLESHOOTING 126
DISPLAY EXPLANATION SOLUTION 127
TROUBLESHOOTING TABLE 132
NO PRINTED IMAGE 133
INCORRECT LABEL POSITIONING 133
SMEARED PRINT IMAGES 133
INTERFACE TROUBLESHOOTING 134
LAN ETHERNET INTERFACE 135
802.11G WIRELESS INTERFACE 135
CENTRONICS INTERFACE 135
HEX DUMP 136
TEST LABEL PRINTING 136
Figure 6-2, Sample Test Label 137
MAINTENANCE 138
CLEANING PROCEDURES 139
PRINT HEAD REPLACEMENT 140
FUSE REPLACEMENT 141
Platen Roller Assy 142
Retaining Bracket 142
Lower Print Assy 142
LABEL SENSOR POSITIONING 143
PRINT HEAD BALANCE ADJUSTMENT 144
PRINT HEAD PRESSURE 145
PRINT HEAD ALIGNMENT 146
RIBBON GUIDE ALIGNMENT 147
RIBBON ROLLER ALIGNMENT 148

Komentáře k této Příručce

Žádné komentáře

SATO GL408e / GL412e Návod k obsluze Strana 38

Komentáře k této Příručce

Související produkty a manuály pro Tiskárny štítků SATO GL408e / GL412e